Kbc-networks WES2HT 9dBi Multipoint Host Manuel d'utilisateur télécharger pdf

Introduction

Welcome to KBC Networks’ Quick Start

Guide for the WES2HT point-to-

multipoint host with 9dBi antennas.

This document provides some tips to get up and

running. More detailed information can be found on

our website (please see Downloads).

Features:

• 5GHz operation

• MIMO technology

• Dynamic Frequency Selection &

Transmission Power Control

• Antenna alignment & signal survey tools

• IP66 casing

• Gigabit Ethernet

System Contents

Qty

Description

1 WES2HT Single point host module with PIM and

power supply

1 Cable weather-proof kit assembly

1 Wall or pole-mount bracket and assembly kit

including:

1 Bracket body

1 Pole clamp bracket

1 Connecting piece 1

1 Connecting piece 2

1 50mm, 1.98” long ¼” hex bolt

2 ¼” hex nuts

1 27mm, 1.06” long ¼” hex bolt

2 Flat washers 15mm, 0.59”

2 Locking washers 10mm, 0.39” long

1 U bolt

2 ¼-20 lock washers

Downloads

Installation manual: for other features & functions:

http://www.kbcnetworks.com/downloads

Specification Sheets:

http://www.kbcnetworks.com/downloads

Equipment Required for Physical Deployment

Two straight-through Ethernet cables are required

for connection from the WES2HT to PoE enabled

switches or PIMs.

Note:

WES2HT requires a CAT6 or Gigabit Ethernet

cable. KBC recommends shielded outdoor rated Ethernet

cables when connecting near power outlets & when

exposed to the elements.

Physical Deployment

This equipment must be installed and operated in

accordance with instructions found in the KBC

Networks manual. The orientation of the units must

be as depicted, failure to comply with these

instructions will invalidate warranty.

Configuring the WES2HT

Host

Note:

The WES2HT comes pre-configured from the

factory and does not require custom settings for basic

operation. Please refer to the documentation provided

for pre-set configuration settings.

If custom settings are required and/or desired,

please set the custom configurations as follows:

Configuring the Host unit:

1. Connect the PIM, PoE 802.3af or 802.3at

compliant sourcing device to the Ethernet

port of the WES2HT Host PoE unit.

2. Allow 60s for the unit to boot.

3. Verify that the static IP address on the

laptop is set to 192.168.1.x subnet.

4. Open a web browser to access the Host on

its 192.168.1.200 IP address; this is the

default address for the unit.

5. Enter the following to access the GUI:

ID: admin Password: admin

Note: Ensure that all other network interface

connections including your laptop Wifi are disabled.

6. Select: <Interference Analyzer> to

determine which frequencies are available

in your location.

Select: one of the available channels

Select: <Apply Settings>

Select: <Save>

Note: Point-to-point Host/APs and their respective

Clients must be MAC locked to each other.

Quick Start

Guide

WES2HT 9dBi

Multipoint Host

QSG-WES2HT_9dBi_MP_Host-Rev1311

www.kbcnetworks.com

1 2

Quick Start 1

Résumé du contenu

Page 1 - Quick Start

Introduction Welcome to KBC Networks’ Quick Start Guide for the WES2HT point-to-multipoint host with 9dBi antennas. This document provides some

Page 2

Topology/Mapping Option If you have chosen the mapping option on your unit you will be able to view system configuration and health all on one pa

Commentaires sur ces manuels

Pas de commentaire

Kbc-networks WES2HT 9dBi Multipoint Host Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour ordinateurs Kbc-networks WES2HT 9dBi Multipoint Host. KBC Networks WES2HT 9dBi Multipoint Host User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour ordinateurs Kbc-networks WES2HT 9dBi Multipoint Host